A0610/hpux/INSTALL
revision: 1998-04-22
----------------------------------------------------------------------


HP ELOQUENCE A.06.10 - Installation Instructions (HP-UX)
========================================================

HP Eloquence requires HP-UX revision 9.0 or above.  HP Eloquence 
A.06.xx is installed in the /opt/eloquence6 directory and will not 
affect any previous HP Eloquence A.05.xx installation.

HP Eloquence files are compressed with GNU zip (gzip). In order 
to install HP Eloquence you need to unpack the files. Gzip is 
included with HP-UX 10.x and above or can be obtained from this 
ftp server in the /pub directory.


Installing on HP-UX 9.x:
------------------------

   As "superuser," follow the steps below to install the HP Eloquence
   software.

   1. Unpack the archive at a temporary location

         gzip -d B1368B.updt.gz

      This unpacks B1368B.updt.gz to B1368B.updt. The compressed
      archive file is deleted.

   2. Run update(1m) by typing:

         /etc/update

   3. Select "Change Source or Destination ->".

   4. Select "From Tape Device to Local System ...".

   5. Tab to the "Source" field and enter the following:

         /tmp/B1368B.updt

      where /tmp is the directory where the B1368B.updt file
      is located.

   6. Press "Done".

   7. Select "Select/View Partitions and Filesets ..."

   8. Activate the HP Eloquence partition(s) you would like to 
      install:
      
      B1368B-A0600     - Base product
      B1368B-A0600-T   - Install a 30 days temporary license key
      B1368B-MIG       - HP260 migration tools

   9. Select "Start Loading".

   10. Type "y" to "Start loading filesets now?".

   11. Check /tmp/update.log to make sure installation completed 
       with no error.


Installing on HP-UX 10.x and HP-UX 11.0
---------------------------------------

   As "superuser," follow the steps below to install the HP Eloquence
   software.

   1. Unpack the archive at a temporary location

         gzip -d B1368B.sd.gz

      This unpacks B1368B.sd.gz to B1368B.sd. The compressed
      archive file is deleted.

   2. Run "swinstall" by typing:

         /usr/sbin/swinstall -s /tmp/B1368B.sd

      where /tmp is the directory where the B1368B.sd file
      is located.

   3. In the Software Selection Window, select/highlight the product
      options you would like to install then choose the "Mark for 
      Install" item from the Actions Menu. 
      The "Marked?" column will automatically be set to "Yes".
      
      The following options are available:
      B1368B         - Install the base software
      B1368B-TLIC    - Install a 30 days temporary license key
      B1368B-ALL     - Install all file sets
      
      When opening the B1368B-ALL bundle, you can enable/disable
      individual product options.
      
   4. Select the "Install (analysis...)" item from the Actions Menu.
      When the analysis is finished with no error, i.e. Status:Ready, 
      click OK.

   5. Click Yes in the Confirmation window to begin the actual
      installation process.

   6. When the installation is completed, a dialog is displayed to 
      notify you that the install task is completed.  You may exit then.


HP-UX 11.0
----------

When installing on HP-UX 11.0 an error message like below may apperar 
during installation. However the installation does succeed.

--- /var/adm/sw/swagent.log ---
       * Beginning the Configure Execution Phase.
ERROR:   You have not specified any fileset selections.  You must
         specify a single fileset when performing file modifications.
ERROR:   The swmodify command failed for
         B1368B-A0600,l=/,r=A.06.10,a=,v=HP.  The configuration process
         will proceed.
ERROR:   Rebuilding the Installed Products Database has failed.  You
         may need to retry this operation.
--- /var/adm/sw/swagent.log ---